qmk-firmware/keyboards/hecomi/rules.mk
takashiski feabafd1f4 define new keyboard "Hecomi" ()
* update pinout for matrix

* first commit

* include split_common.h

* change split_common.h to split_util.h

* update config.h

* update keymap & config

* update

* remove K70, add K77

* fixed test keymap

* add Layer

* define to HHKB pro 2 based keymap

* change authoer name

* define LAYOUT and LAYOUT_KC

* replace from LAYOUT_KC to LAYOUT

* change name hecomi_alpha to hecomi/alpha

* fixed hecomi_alpha to hecomi/alpha

* remove unnecessary files

* update readme

* add DEFAULT_FOLDER

* remove hecomi_alpha because change name to hecomi

* remove bad LAYOUT macro

* remove IS_COMMAND macro

* remove unnecessary RGB options

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/alpha/rules.mk

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/alpha/rules.mk

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* remove endif

* update rule.mk with suggestions
2019-02-16 21:44:08 -08:00

86 lines
3.3 KiB
Makefile

DEFAULT_FOLDER=hecomi/alpha
#
#
# MCU name
#MCU = at90usb1286
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
SPLIT_KEYBOARD = yes