History

QMK Bot 8f867c1bef Merge remote-tracking branch 'origin/master' into develop		2020-12-21 14:39:10 +00:00
..
keymaps
.noci	Initial list of keyboards to exclude from CI (#11213 )	2020-12-21 15:38:39 +01:00
chconf.h	ChibiOS upgrade: keyboard conf migrations (phase 1) (#10418 )	2020-12-05 21:13:58 +11:00
config.h
halconf.h	ChibiOS upgrade: keyboard conf migrations (phase 1) (#10418 )	2020-12-05 21:13:58 +11:00
info.json
mcuconf.h	ChibiOS upgrade: keyboard conf migrations (phase 1) (#10418 )	2020-12-05 21:13:58 +11:00
readme.md
rules.mk	Add STM32Duino to bootloader selection (#10558 )	2020-10-13 03:19:50 +11:00
z150.c
z150.h

readme.md

QMK-based firmware for Zenith Z-150 keyboard

Zenith Z-150 keyboard conversion project: direct connection of Black Pill to the matrix.

Keyboard Maintainer: DmNosachev
Hardware Supported: Zenith Z-150 keyboard, 100-1860 version with white logo, Black Pill STM32F103C8T6 MCU board. Alternatevely you can use any MCU which is supported by QMK and has 22 or more IO pins: Arduino Micro, Teensy 2.0, Teensy 2.0++, Blue Pill, etc.

Earlier 100-1886 version with black logo has different PCB.

Make example for this keyboard (after setting up your build environment):

make handwired/z150:default

See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.

Modding

Matrix

Z-150 has 11x8 matrix. It's ghost-free thanks to the diodes.

Columns are located under NEC D8049HC MCU IC:

Rows are connected to unmarked 24-pin MUX IC:

LEDs

LEDs (from left to right): NumLock, CapsLock, ScrollLock:

Their anodes are connected to VCC through 220Ω resistors.

You can keep the original resistors, but with Black Pill or any other 3.3V controller the LEDs may seem a little dim. Try 150Ω or close value if you want to fix that.

Black Pill

Suggested mount position for the Black Pill (view from the bottom side of the PCB):

      R0  R1  R2  R3  R4  R6          R9  LC  LN  LS
,--------------------------------------------------------------------,
|B12 B13 B14 B15  A8  A9 A10 A11 A12 A15  B3  B4  B5  B6  B7 3V3 GND |---,
|                                                                    |USB|
|B11 B10  B1  B0  A7  A6  A5  A4  A3  A2  A1  A0 RST C13  B9  B8 GND |---'
'--------------------------------------------------------------------'
  C0  C1  C2  C3  C4  C5  C6  C7  R5  R8  R7  RA

Desolder all ICs, crystal oscillator, capacitors and resistors except R0–R2 (they connect LEDs to VCC).
Solder 12-pin header to the Black Pill (pins B11–A0 on the left side).
Solder two 3-pin headers for boot jumpers.
Solder 4-pin SWD header.
Burn STM32duino bootloader to Black Pill.
Compile and flash the firmware: make handwired/z150:default:flash
Align Black Pill pins B11–A4 with columns 0–7 and solder them.
Connect rows, LEDs, ground and VCC traces to the corresponding pins of the BlackPill using additional wires.