1646c0f26c
* Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only |
||
|---|---|---|
| .. | ||
| config.h | ||
| glcdfont_godspeed.c | ||
| glcdfont_laser.c | ||
| glcdfont_pulse.c | ||
| glcdfont.c | ||
| keymap.c | ||
| readme.md | ||
| rules.mk | ||
Corne keyboard layout
This is my highly personalized CRKBD layout. I use Colemak DHm as main typing layer. I use this keyboard and layout in my daily programming job and for everything at home, including gaming.
This keymap is the result of an evolution from Ultimate Hacking Keyboard to Iris, to Corne. It took many iterations and changes and only now I feel this is ready to be merged into the main QMK repository, because I think further changes will be minor. This is my 1.0 release so to speak.
Many thanks to foostan for the keyboard, all QMK contributors and drashna specifically for his work on this keyboard.
Layers
COLEMAKDHM
Main typing layer. I really love having SHIFT available on thumbs. I am a left thumb space bar person, so I put SPACE there and ENTER on right. I use CTRL key combos lot in my text editor and desktop environment. That's why I have two of them. I also found them to be a great position for the square brackets. ([ and ]). These become parenthesis (( and )) on either of the layers.
Holding SHIFT while tapping BACKSPACE will output DEL. Holding both SHIFT keys will output SHIFT+DEL.
I don't know about you but "lower" and "raise" don't mean that much to me. I named my layers SYM, short for symbols and NAV, short for navigation. Holding the key will activate the layer for as long as it is held, double tapping it will switch to it. Single tapping it once will switch to main layer again.
Holding TAB will access NUM layer which features a numpad.
SYM
Includes a number row, the symbols normally on SHIFT and numbers, as well as a numpad under right side homing keys.
NAV
This is where I access arrow keys, page up, down, home, end and F keys. I also added general tab forward and backward keys. Tab close and window close. I primarily use these in my browser, terminal and text editor.
UTIL
Short for utility. This is accessed by pressing both SYM and NAV at the same time. It has a software RESET key, media keys, RGB control and switches main layer between Colemak and a gaming layer.
NUMPAD
This gives access to a numpad on the right half with some additional symbols I find useful when using the numpad.
GAMING
Sometimes I switch to type in Discord, Steam, or in game chat, so I think it's more important to keep typing functional than put WASD on where I want movement to be. This means I rebind my keys in all games. It's worth it to me.
I put movement on FRST (would be ESDF on QWERTY), because it lines up more comfortably with the columnar staggered layout of the Corne. It also gives more easy access to all keys on left half.
Most notable here is that there are no tap and hold differences anymore on left hand side besides the new layer key. This is a different layer than SYM.
GAMING_EXT
This is the gaming extended layer where movement keys remain the same. This means I can keep moving while accessing second layer keys. All other keys are keys on which I can easily rebind something. Besides that it gives me an ENTER key which does not switch. This is good when a game requires you to hold ENTER.
RGB
I took a big inspiration from Drashna's RGB configuration and tweaked it.
RGB_UND: Toggles underglow indicators on and off. Each layer has its own color.RGB_IDL: This will enable/disable idle mode. By default, when typing, theDISABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUSwill be used. When the idle timeout has exceeded the secondary animation will be activated, which isRGB_MATRIX_CYCLE_ALLby default. When switching toGAMINGlayer the timeout will be reduced and the idle animation changed toRGB_MATRIX_RAINBOW_PINWHEELS. When idle mode is enabled,RGB_MATRIX_TYPING_HEATMAPandRGB_MATRIX_MULTISPLASHwill be used for active animation. All others for idle animation. When disabling idle mode, the current idle animation will be activated. Additionally, on idling, the underglow layer indication will be deactivated.- There are no RGB mode cycle keys, but instead several keys to use a specific RGB directly. Each has their own default speed, although this can be changed.
Building
make crkbd/rev1:rpbaptist:dfu
Notes
I use several OLED slave side images, depending on the keycaps I am using. These also determine the default LED color and underglow.
make crkbd/rev1:rpbaptist:dfu THEME=pulse
Current supported themes are:
- godspeed
- laser
- pulse