qmk-firmware/quantum/mcu_selection.mk

571 lines
16 KiB
Makefile
Raw Normal View History

2020-08-25 10:58:00 +02:00
MCU_ORIG := $(MCU)
ifneq ($(findstring MKL26Z64, $(MCU)),)
# Cortex version
MCU = cortex-m0plus
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = KL2x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MKL26Z64
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= kl2x
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_LC
endif
ifneq ($(findstring MK20DX128, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK20DX128
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= k20x5
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3
endif
ifneq ($(findstring MK20DX256, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK20DX256
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= k20x7
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3_1
endif
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
ifneq ($(findstring MK66F18, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = MK66F18
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK66FX1M0
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= MK66F18
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3_6
endif
ifneq ($(findstring STM32F042, $(MCU)),)
# Cortex version
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F042x6
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f0xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F042X6
USE_FPU ?= no
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F0
endif
ifneq ($(findstring STM32F072, $(MCU)),)
# Cortex version
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F072xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f0xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F072XB
USE_FPU ?= no
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F0
endif
ifneq ($(findstring STM32F103, $(MCU)),)
# Cortex version
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F1xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F103x8
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f1xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F103
USE_FPU ?= no
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F1
endif
ifneq ($(findstring STM32F303, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F3xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F303xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f3xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F303XC
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F3
endif
ifneq ($(findstring STM32F401, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F401xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= BLACKPILL_STM32_F401
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F4
endif
ifneq ($(findstring STM32F411, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
ifeq ($(strip $(BOOTLOADER)), tinyuf2)
MCU_LDSCRIPT ?= STM32F411xE_tinyuf2
FIRMWARE_FORMAT ?= uf2
else
MCU_LDSCRIPT ?= STM32F411xE
endif
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= BLACKPILL_STM32_F411
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32F4
endif
ifneq ($(findstring STM32F446, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F446xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F446XE
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
endif
ifneq ($(findstring STM32G431, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32G4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32G431xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32g4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_G431XB
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32G4
endif
ifneq ($(findstring STM32G474, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32G4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32G474xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32g4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_G474XE
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
2021 May 29 Breaking Changes Update (#13034) * Add Per Key functionality for AutoShift (#11536) * LED Matrix: Reactive effect buffers & advanced indicators (#12588) * [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626) * [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625) * LED Matrix: Split (#12633) * [CI] Format code according to conventions (#12650) * feat: infinite timeout for leader key (#6580) * feat: implement leader_no_timeout logic * docs(leader_key): infinite leader timeout docs * Format code according to conventions (#12680) * Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403) * Fix default ADC_RESOLUTION for ADCv3 (and ADCv4) Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers (that macro should not have been there, because ADCv3 has CFGR instead of CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS if it is defined (that name is used for ADCv3 and ADCv4). * Update ADC docs to match the actually used resolution ADC driver for ChibiOS actually uses the 10-bit resolution by default (probably to match AVR); fix the documentation accordingly. Also add both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names differ according to the ADC implementation in the particular MCU). * Fix pinToMux() for B12 and B13 on STM32F3xx Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and B13 pins were wrong. * Add support for all possible analog pins on STM32F1xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx (they are the same at least for STM32F103x8 and larger F103 devices, and also F102, F105, F107 families). Actually tested on STM32F103C8T6 (therefore pins C0...C5 were not tested). Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages, cannot be supported at the moment, because those pins are connected only to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1. * Add support for all possible analog pins on STM32F4xx Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are apparently the same for all F4xx devices, except some smaller devices may not have ADC3. Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested. Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices which don't have ADC3 also don't have the GPIOF port, therefore the code which refers to Fx pins does not compile. * Fix STM32F3xx ADC mux table in documentation The ADC driver documentation had some errors in the mux table for STM32F3xx. Fix this table to match the datasheet and the actual code (mux settings for B12 and B13 were also tested on a real STM32F303CCT6 chip). * Add STM32F1xx ADC pins to the documentation * Add STM32F4xx ADC pins to the documentation * Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600) * Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example. * Update flashing.md * Update chconf.h * Update config.h * Update halconf.h * Update mcuconf.h * eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671) * Add support for MCU = STM32F446 (#12619) * Add support for MCU = STM32F446 * Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h * Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64 * stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled. * Format code according to conventions (#12682) * Format code according to conventions (#12687) * Add STM32L433 and L443 support (#12063) * initial L433 commit * change to XC * fix L433 * disable all peripherals * update system and peripheral clocks * 433 change * use its own board files * revert its own board files * l433 specific change * fix stm32l432xx define * remove duplicate #define * fix bootloader jump * move to L443xx and add i2c2, spi2, usart3 to mcuconf.h * move to L443 * move to L443 * fix sdmmc in mcuconf.h * include STM32L443 * add L443 * Include L443 in compatible microcontrollers * Include L443 in compatible microcontrollers * Update config bootloader jump description * Update ChibiOS define reasoning * Update quantum/mcu_selection.mk * fix git conflict * Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613) * Fix bad PR merge for #6580. (#12721) * Change RGB/LED Matrix to use a simple define for USB suspend (#12697) * [CI] Format code according to conventions (#12731) * Fixing transport's led/rgb matrix suspend state logic (#12770) * [CI] Format code according to conventions (#12772) * Fix comment parsing (#12750) * Added OLED fade out support (#12086) * fix some references to bin/qmk that slipped in (#12832) * Resolve a number of warnings in `qmk generate-api` (#12833) * New command: qmk console (#12828) * stash poc * stash * tidy up implementation * Tidy up slightly for review * Tidy up slightly for review * Bodge environment to make tests pass * Refactor away from asyncio due to windows issues * Filter devices * align vid/pid printing * Add hidapi to the installers * start preparing for multiple hid_listeners * udev rules for hid_listen * refactor to move closer to end state * very basic implementation of the threaded model * refactor how vid/pid/index are supplied and parsed * windows improvements * read the report directly when usage page isn't available * add per-device colors, the choice to show names or numbers, and refactor * add timestamps * Add support for showing bootloaders * tweak the color for bootloaders * Align bootloader disconnect with connect color * add support for showing all bootloaders * fix the pyusb check * tweaks * fix exception * hide a stack trace behind -v * add --no-bootloaders option * add documentation for qmk console * Apply suggestions from code review * pyformat * clean up and flesh out KNOWN_BOOTLOADERS * Remove pointless SERIAL_LINK_ENABLE rules (#12846) * Make Swap Hands use PROGMEM (#12284) This converts the array that the Swap Hands feature uses to use PROGMEM, and to read from that array, as such. Since this array never changes at runtime, there is no reason to keep it in memory. Especially for AVR boards, as memory is a precious resource. * Fix another bin/qmk reference (#12856) * [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419) * Fixup build errors on `develop` branch. (#12723) * LED Matrix: Effects! (#12651) * Fix syntax error when compiling for ARM (#12866) * Remove KEYMAP and LAYOUT_kc (#12160) * alias KEYMAP to LAYOUT * remove KEYMAP and LAYOUT_kc * Add setup, clone, and env to the list of commands we allow even with broken modules (#12868) * Rename `point_t` -> `led_point_t` (#12864) * [Keyboard] updated a vendor name / fixed minor keymap issues (#12881) * Add missing LED Matrix suspend code to suspend.c (#12878) * LED Matrix: Documentation (#12685) * Deprecate `send_unicode_hex_string()` (#12602) * Fix spelling mistake regarding LED Matrix in split_common. (#12888) * [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895) * Use milc.subcommand.config instead of qmk.cli.config (#12915) * Use milc.subcommand.config instead * pyformat * remove the config test * Add function to allow repeated blinking of one layer (#12237) * Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time * Update doc * Rework rgblight blinking according to requested change * optimize storage * Fixup housekeeping from being invoked twice per loop. (#12933) * matrix: wait for row signal to go HIGH for every row (#12945) I noticed this discrepancy (last row of the matrix treated differently than the others) when optimizing the input latency of my keyboard controller, see also https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/ Before this commit, when tuning the delays I noticed ghost key presses when pressing the F2 key, which is on the last row of the keyboard matrix: the dead_grave key, which is on the first row of the keyboard matrix, would be incorrectly detected as pressed. After this commit, all keyboard matrix rows are interpreted correctly. I suspect that my setup is more susceptible to this nuance than others because I use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask the problem. * ensure we do not conflict with existing keymap aliases (#12976) * Add support for up to 4 IS31FL3733 drivers (#12342) * Convert Encoder callbacks to be boolean functions (#12805) * [Keyboard] Fix Terrazzo build failure (#12977) * Do not hard set config in CPTC files (#11864) * [Keyboard] Corne - Remove legacy revision support (#12226) * [Keymap] Update to Drashna keymap and user code (based on develop) (#12936) * Add Full-duplex serial driver for ARM boards (#9842) * Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987) * Backlight: add defines for default level and breathing state (#12560) * Add dire message about LUFA mass storage bootloader (#13014) * [Keyboard] Remove redundant legacy and common headers for crkbd (#13023) Was causing compiler errors on some systems. * Fix keyboards/keymaps for boolean encoder callback changes (#12985) * `backlight.c`: include `eeprom.h` (#13024) * Add changelog for 2021-05-29 Breaking Changes merge (#12939) * Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version * Add recent develop changes * Sort recent develop changes * Remove sections for ChibiOS changes per tzarc No ChibiOS changes this round. * Add and sort recent develop changes * add notes about keyboard moves/deletions * import changelog for PR 12172 Documents the change to BOOTMAGIC_ENABLE. * update section headings * re-sort changelog * add additional note regarding Bootmagic changes * remove changelog timestamp * update dates in main Breaking Changes docs * fix broken section anchors in previous changelogs * add link to backlight/eeprom patch to changelog * highlight some more changes * link PRs from section headers * Restore standard readme * run: qmk cformat --core-only
2021-05-29 23:38:50 +02:00
# UF2 settings
UF2_FAMILY ?= STM32G4
endif
ifneq (,$(filter $(MCU),STM32L433 STM32L443))
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32L4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32L432xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32l4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_L433XC
PLATFORM_NAME ?= platform_l432
USE_FPU ?= yes
# Options to pass to dfu-util when flashing
DFU_ARGS ?= -d 0483:DF11 -a 0 -s 0x08000000:leave
DFU_SUFFIX_ARGS ?= -v 0483 -p DF11
# UF2 settings
UF2_FAMILY ?= STM32L4
endif
ifneq (,$(filter $(MCU),at90usb162 atmega16u2 atmega32u2 atmega16u4 atmega32u4 at90usb646 at90usb647 at90usb1286 at90usb1287))
PROTOCOL = LUFA
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU ?= 16000000
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB ?= $(F_CPU)
# Interrupt driven control endpoint task
ifeq (,$(filter $(NO_INTERRUPT_CONTROL_ENDPOINT),yes))
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
endif
ifneq (,$(filter $(MCU),at90usb162 atmega16u2 atmega32u2))
2020 November 28 Breaking Changes Update (#11053) * Branch point for 2020 November 28 Breaking Change * Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183) * Add support for soft serial to ATmega32U2 (#10204) * Change MIDI velocity implementation to allow direct control of velocity value (#9940) * Add ability to build a subset of all keyboards based on platform. * Actually use eeprom_driver_init(). * Make bootloader_jump weak for ChibiOS. (#10417) * Joystick 16-bit support (#10439) * Per-encoder resolutions (#10259) * Share button state from mousekey to pointing_device (#10179) * Add hotfix for chibios keyboards not wake (#10088) * Add advanced/efficient RGB Matrix Indicators (#8564) * Naming change. * Support for STM32 GPIOF,G,H,I,J,K (#10206) * Add milc as a dependency and remove the installed milc (#10563) * ChibiOS upgrade: early init conversions (#10214) * ChibiOS upgrade: configuration file migrator (#9952) * Haptic and solenoid cleanup (#9700) * XD75 cleanup (#10524) * OLED display update interval support (#10388) * Add definition based on currently-selected serial driver. (#10716) * New feature: Retro Tapping per key (#10622) * Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638) * Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530) * Rescale both ChibiOS and AVR backlighting. * Reduce Helix keyboard build variation (#8669) * Minor change to behavior allowing display updates to continue between task ticks (#10750) * Some GPIO manipulations in matrix.c change to atomic. (#10491) * qmk cformat (#10767) * [Keyboard] Update the Speedo firmware for v3.0 (#10657) * Maartenwut/Maarten namechange to evyd13/Evy (#10274) * [quantum] combine repeated lines of code (#10837) * Add step sequencer feature (#9703) * aeboards/ext65 refactor (#10820) * Refactor xelus/dawn60 for Rev2 later (#10584) * add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824) * [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549) * update chibios os usb for the otg driver (#8893) * Remove HD44780 References, Part 4 (#10735) * [Keyboard] Add Valor FRL TKL (+refactor) (#10512) * Fix cursor position bug in oled_write_raw functions (#10800) * Fixup version.h writing when using SKIP_VERSION=yes (#10972) * Allow for certain code in the codebase assuming length of string. (#10974) * Add AT90USB support for serial.c (#10706) * Auto shift: support repeats and early registration (#9826) * Rename ledmatrix.h to match .c file (#7949) * Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231) * Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840) * Merge point for 2020 Nov 28 Breaking Change
2020-11-28 21:02:18 +01:00
NO_I2C = yes
endif
endif
ifneq (,$(filter $(MCU),atmega32a))
# MCU name for avrdude
AVRDUDE_MCU = m32
PROTOCOL = VUSB
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
F_CPU ?= 12000000
endif
2019-09-07 17:24:19 +02:00
ifneq (,$(filter $(MCU),atmega328p))
# MCU name for avrdude
AVRDUDE_MCU = m328p
2019-09-07 17:24:19 +02:00
PROTOCOL = VUSB
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
F_CPU ?= 16000000
endif
ifneq (,$(filter $(MCU),atmega328))
# MCU name for avrdude
AVRDUDE_MCU = m328
PROTOCOL = VUSB
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
F_CPU ?= 16000000
endif
ifneq (,$(filter $(MCU),attiny85))
PROTOCOL = VUSB
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
F_CPU ?= 16500000
endif